|
RESUME:
Rolando Martinez
SKILLS:
Electronics. Inspecting, repairing, modifying and designing complex electronic circuit in a wide spectrum of applications.
Basic knowledge of Communication Systems.
Metrology and Calibrations. Perform verification/calibrations of
a wide range of measuring equipment of radio and electrical magnitudes at any level of complexity following International
or Military procedures. Interpret and apply International Standards from ISO, IEC and other International Organizations. Determination
of Measurement's Uncertainty.
EDUCATION:
*1996 Institute of Metrological Research. Havana, Cuba
Standard
ISO 10012 Assurance of Quality of Measurements.
*1991 Center of Computer Science Training. Havana, Cuba
Microprocessor
Z-80.
*1987 Center of Computer Science Training. Havana, Cuba
Exploitation of Microcomputer Systems.
*1981
Jose A. Echeverria Higher Polytechnic Institute. Havana, Cuba
Microprocessor Application and Study.
*1981
Standards State Committee. Havana, Cuba
Radio technical Measurements.
* 1979 Jose A. Echeverria Higher Polytechnic
Institute. Havana, Cuba
Communication Sistems.
*1972-1978 Jose A. Echeverria Higher Polytechnic Institute.
Havana, Cuba
Electrical Engineer. (Certified by Josef Silny & Associates, Inc. as equivalent of the U.S. degree
of Bachelor Science in Electrical Engineering).
PROFESSIONAL EXPERIENCE:
*2008-2023 Technical Maintenance,
Inc Miramar, FL
Same as Kimball Electronic Lab. plus pressure gauges,
calipers, force gauges, chart recorders , temperature and humidity transmitters, thermometers and thread plugs.
*2001-2008 Kimball Electronic Laboratory, Inc. Miami,
FL
Technician. Calibrating, troubleshooting, repairing, aligning and using: frequency counters, analog/digital oscilloscopes,
signal generators of any range of frequency, pulse/function generators, spectrum analyzers, power meters/sensors, network
analyzers, AC/DC power supplies, vectorscopes, TV signal generators, measuring receivers, attenuators, communication test
sets, navigation test sets, XPDR/DME test sets, altimeter test sets, radar test sets, voltage dividers, ratio transformers,
digital/analogical multimeters, LCR meters, calibrators, capacitance/resistance/inductance standards, bridges, temperature
indicators, ovens, micrometers and scales.
Interpreted and applied: schematics, specifications, technical orders,
commercial data, fault isolation aids, mathematic expressions and conversions.
Instructed technicians in proper use,
alignment, troubleshooting techniques and calibrations of measuring instruments. Also in the proper use of procedures and
documentation.
Used calibration software as Lab-Mate and Indi Soft.
Packed and transported equipment safely
to customer facilities to perform calibrations on site to accommodate customer needs.
Performed flawless equipment
calibrations during A2LA certification contributing to certify the laboratory A2LA accreditation. Discussing with the auditors
the uncertainty budget of the laboratory.
*2000-2001 Synergy Labs, Inc. Miami, FL
Technician. Calibrating,
troubleshooting, repairing, aligning and using: frequency counters, analog/digital oscilloscopes, signal generators of any
range of frequency, pulse/function generators, spectrum analyzers, power meters/sensors, network analyzers, AC/DC power supplies,
measuring receivers, attenuators, communication test sets, navigation test sets, XPDR/DME test sets, altimeter test sets,
radar test sets, voltage dividers, ratio transformers, digital/analogical multimeters, LCR meters, calibrators, capacitance/resistance/inductance
standards, bridges, and temperature indicators.
Interpreted and applied: schematics, specifications, technical
orders, commercial data, fault isolation aids, mathematic expressions and conversions.
Used calibration software as
Met-Cal.
Packed and transported equipment safely to customer facilities to perform calibrations on site to accommodate
customer needs.
*1994-1999 Metrological Center of Holguin. Holguin, Cuba
Engineer. Calibrating, troubleshooting,
repairing, aligning and using: frequency counters, analog/digital oscilloscopes, signal generators of any range of frequency,
pulse/function generators, spectrum analyzers, power meters/sensors, AC/DC power supplies, attenuators, voltage dividers,
digital/analogical multimeters, LCR meters, calibrators, capacitance/resistance/inductance standards, bridges, and temperature
indicators.
Interpreted and applied: schematics, specifications, technical orders, commercial data, fault isolation
aids, mathematic expressions and conversions
Performed as manager of a Department comprising four laboratories (Temperature,
Radio, Electricity and Physical-Chemical Magnitudes.
Performed as a Metrological Assurance consultant.
*1988-1994.
National Institute of Automated System and Computer Science. Havana, Cuba
Engineer. Performed as Metrological Assurance
Specialist.
*1978-1988. Armed Forces Metrological Center. (As a civilian) Havana, Cuba
Engineer. Calibrating,
troubleshooting, repairing, aligning and using: frequency counters, analog/digital oscilloscopes, signal generators of any
range of frequency, pulse/function generators, spectrum analyzers, power meters/sensors, AC/DC power supplies, attenuators,
voltage dividers, digital/analogical multimeters, LCR meters, calibrators, capacitance/resistance/inductance standards, and
bridges.
Performed high precision measurements.
Performed as Metrological Assurance Specialist
AWARDS
RECEIVED:
*1999 Cuba. National Office of Standardization. Recognition Diploma for the scientific result of Organization
of the Metrological Assurance and Projection of the Calibration Laboratory in the MOA Nickel, S.A. Company.
*1998
Cuba. National Office of Standardization. Diploma for recognition of 20 years of permanence in the field of Standardization,
Metrology and Quality Control.
|
